Running out of a color halfway through a project is annoying; running out after the shop has changed dye lots is worse. Buying three of everything "to be safe" gets expensive on a 40-color portrait. The answer is a quick estimate per color, based on three things: how much thread is in a skein, how much one stitch uses, and how many stitches of that color the pattern has.
What is in a DMC skein
A standard DMC six-strand embroidery floss skein (Article 117) is 8 metres (8.7 yards) long. For cross-stitch you separate the six strands and stitch with one, two or three of them together. So one skein gives you:
| Strands used | Usable length per skein | Typical fabric |
|---|---|---|
| 1 | 48 m (6 × 8 m) | 18 ct for a light look, 22 ct, 28 ct over 1 |
| 2 | 24 m (3 × 8 m) | 14, 16, 18 ct Aida; 28 ct over 2 |
| 3 | 16 m (2 × 8 m) | 11 ct Aida |
Two strands is the common default, and it is what StitchGrid assumes unless you change it.
How much thread one stitch uses
A full cross covers one square of the fabric. On the front, the thread runs along both diagonals. On the back it travels, usually vertically, to the start of the next leg. Stitched in rows (all the "/" legs first, then back along the row with the "\" legs), each stitch uses about two diagonals plus two sides of the square:
thread per stitch ≈ square side × (2 × 1.414 + 2) ≈ 4.83 × square side
The square side is 25.4 mm divided by the fabric count. That gives a theoretical minimum, before any waste:
| Fabric | Square side | Thread per stitch | Stitches per skein, 2 strands, no waste |
|---|---|---|---|
| 11 ct | 2.31 mm | 11.1 mm | about 2,150 (about 1,430 with 3 strands) |
| 14 ct / 28 over 2 | 1.81 mm | 8.8 mm | about 2,740 |
| 16 ct | 1.59 mm | 7.7 mm | about 3,130 |
| 18 ct | 1.41 mm | 6.8 mm | about 3,520 |
Add waste, generously
Nobody stitches with zero waste. Thread goes into starting and finishing tails, travelling across the back between areas of the same color, the bit left in the needle when a length runs out, and the occasional unpicked mistake. How much depends on the pattern and on you:
- Large solid areas (backgrounds, a dark coat) waste little, perhaps 15–25%.
- Scattered colors and confetti waste a lot, because a whole tail is spent on a few stitches. 50% or more is realistic.
- Loop start versus knots and tails: the loop start saves a tail at the beginning of each length, which adds up.
A cautious planning figure that covers most patterns is about 1,600–1,800 full stitches per skein on 14-count with two strands, roughly the theoretical figure minus a third. On 16 or 18-count you get more stitches per skein, on 11-count fewer. Always round up to whole skeins, and for colors with a large count consider one extra skein from the same dye lot.
A worked example
A 100 × 80 stitch pet portrait on 14-count Aida, two strands, fully stitched (8,000 stitches), with seven colors. Using 1,700 stitches per skein as the planning figure:
| DMC | Color | Stitches | Skeins (stitches ÷ 1,700) | Buy |
|---|---|---|---|---|
| 310 | Black | 2,600 | 1.53 | 2 |
| 3865 | Winter white | 2,100 | 1.24 | 2 |
| 3371 | Black brown | 1,000 | 0.59 | 1 |
| 801 | Dark coffee brown | 800 | 0.47 | 1 |
| 738 | Very light tan | 700 | 0.41 | 1 |
| 3778 | Light terra cotta | 500 | 0.29 | 1 |
| 3866 | Ultra very light mocha brown | 300 | 0.18 | 1 |
| Total | 8,000 | 9 skeins | ||
Two of the seven colors need a second skein. The five small colors each use well under one skein, so if you already have them in your stash, check the remaining length rather than buying new. If the background were left unstitched, the 310 and 3865 counts would fall and so would the total.
The same pattern on 18-count would finish at 5.6 × 4.4 inches instead of 7.1 × 5.7 (see the size calculator) and, because each stitch is smaller, would need roughly a fifth to a quarter less floss.
Things that change the estimate
- Half stitches and quarter stitches use roughly half a full stitch's thread, but they often come with extra starts and stops.
- Backstitch is measured by length, not by count. One stitch along a square side uses roughly two square sides of thread. A few long outlines rarely need more than one skein.
- Blended needles (one strand each of two colors) use half as much of each color as a two-strand stitch of one color.
- Tension. Tight stitchers use a little less; anyone who stitches "in the hand" rather than on a frame tends to use a little more.
How StitchGrid estimates skeins
The floss list counts stitches per DMC color and turns them into skeins using the fabric count and number of strands you choose, with an allowance for waste, then rounds up. It is an estimate made on the same principles as above, not a guarantee. For a big project with a dominant color, buy that color from one dye lot at the start.
Make your pattern and the floss list shows stitch counts and skeins per DMC color, ready to take to the shop.
Get a floss list for your photoFewer colors means fewer skeins and less waste. If your list is long, read how many colors to use for ways to trim it without losing the picture.